LOT 47
c.1952 Nimbus 750cc Model C Four Frame no. 10749 Engine no. 12783
Sold for €5,376 inc. premiumLot to be sold without reserve
Lot 47
c.1952 Nimbus 750cc Model C Four
c.1952 Nimbus 750cc Model C Four
Frame no. 10749
Engine no. 12783
Frame no. 10749
Engine no. 12783
Please kindly note that this motorbike will be available for viewing by prior appointment in Dortmund: please contact [email protected] for booking.
The result of diversification by the Danish vacuum cleaner manufacturer, Fisker & Nielsen, the Nimbus motorcycle first appeared in 1919. Unusually, only inline four-cylinder models were built. These were of advanced design, using shaft final drive and pressed steel frames right from the start of production, and pioneered the use of the telescopic front fork in the mid-1930s. The early models featured a distinctive tubular spine frame that doubled as the fuel tank, soon gaining the nickname 'stovepipe'. The low-compression Nimbus engine was noted for its smoothness and flexibility.
In 1928, motorcycle production was suspended to enable the company to concentrate on producing its Nilfisk vacuum cleaners, and when the new Nimbus appeared in 1934 it was with a power unit that showed strong motor-industry influence, being constructed along car lines with integral crankcase/cylinder block in cast iron and a detachable alloy sump. The cast-iron one-piece cylinder head was topped by an alloy housing for the single overhead camshaft, which was driven by shaft-and-bevel gears. A single-plate clutch transmitted power to the three-speed gearbox. The original 'stovepipe' frame had been superseded by one made from flat spring steel, while foot change for the gearbox, a beefier front fork, and larger brakes had been added by the end of the 1930s. Nimbus was ahead of its time in many ways, introducing its first telescopic front fork in 1934 and adopting closed-circuit crankcase ventilation many years before the automobile industry.
From then onwards the Nimbus changed little until series production was ended in 1954, once again to free up resources for the vacuum cleaner business. An additional few machines were assembled from spares between 1954 and 1959 but none have been made since then. Production was always on a limited scale, but such is the quality of the Nimbus that many remain in service today.
This Nimbus Four comes with two instruction manuals (in Danish); a German Abmeldebescheinigung (de-registration document) from the 1970s; and a German Kraftfahrzeugbrief (registration document).
Key not required
The result of diversification by the Danish vacuum cleaner manufacturer, Fisker & Nielsen, the Nimbus motorcycle first appeared in 1919. Unusually, only inline four-cylinder models were built. These were of advanced design, using shaft final drive and pressed steel frames right from the start of production, and pioneered the use of the telescopic front fork in the mid-1930s. The early models featured a distinctive tubular spine frame that doubled as the fuel tank, soon gaining the nickname 'stovepipe'. The low-compression Nimbus engine was noted for its smoothness and flexibility.
In 1928, motorcycle production was suspended to enable the company to concentrate on producing its Nilfisk vacuum cleaners, and when the new Nimbus appeared in 1934 it was with a power unit that showed strong motor-industry influence, being constructed along car lines with integral crankcase/cylinder block in cast iron and a detachable alloy sump. The cast-iron one-piece cylinder head was topped by an alloy housing for the single overhead camshaft, which was driven by shaft-and-bevel gears. A single-plate clutch transmitted power to the three-speed gearbox. The original 'stovepipe' frame had been superseded by one made from flat spring steel, while foot change for the gearbox, a beefier front fork, and larger brakes had been added by the end of the 1930s. Nimbus was ahead of its time in many ways, introducing its first telescopic front fork in 1934 and adopting closed-circuit crankcase ventilation many years before the automobile industry.
From then onwards the Nimbus changed little until series production was ended in 1954, once again to free up resources for the vacuum cleaner business. An additional few machines were assembled from spares between 1954 and 1959 but none have been made since then. Production was always on a limited scale, but such is the quality of the Nimbus that many remain in service today.
This Nimbus Four comes with two instruction manuals (in Danish); a German Abmeldebescheinigung (de-registration document) from the 1970s; and a German Kraftfahrzeugbrief (registration document).
Key not required
Footnotes
Please kindly note that VAT at the prevailing german rate (currently 19%) will be added to the buyer's premium which will be invoiced on a VAT exclusive basis. If you are planning to export, please make the department aware.









Additional information
Looking for a similar item?
Our Motorcycles specialists can help you find a similar item at an auction or via a private sale.
Find your local specialistBid now on these items
United Kingdom
Coming soon
1971 Kawasaki 500 Mach III
£3,000 - £5,000
United Kingdom
Coming soon
1926 Triumph 494cc
£4,000 - £6,000
United Kingdom
Coming soon
1934 Austin Seven 65
£4,000 - £6,000
United Kingdom
Coming soon
1936 Austin 7 Ruby,
£3,200 - £4,000
United Kingdom
Coming soon
Triumph 5T
£3,000 - £4,000
United Kingdom
Coming soon
Triumph Tiger 100
£3,000 - £4,000
United Kingdom
Coming soon
1915 Douglas 350cc 2¾hp
£4,000 - £5,000
United Kingdom
Coming soon
Triumph 6T
£3,000 - £4,000
United Kingdom
Coming soon
Triumph 6T
£3,000 - £4,000
United Kingdom
Coming soon
1921 Triumph 550cc Model H
£4,000 - £5,000
United Kingdom
Coming soon
1916 Radco 211cc
£3,400 - £4,400
United Kingdom
Coming soon
1974 Moto Guzzi 750S
£4,000 - £6,000
United Kingdom
A Michaux & Cie Velocipede, circa 1870,
£4,000 - £6,000
















